Replace Nissan Key Fob Batteries
If your Nissan keyfob doesn't respond your commands, the battery could be dead. This is a simple fix that the majority of people can handle themselves.
To replace nissan smart key can purchase a new one at a hardware store or consult your owner's guide for the model you have.
The Battery is changed
The key fob on your Nissan model comes with a built-in battery that eventually loses its charge. Luckily, changing the battery on the key fob is an easy process that takes just a few minutes to complete. First, you'll have to purchase an additional CR2032 3V battery. It's a tiny coin cell battery that is often used in key fobs, and is available at all convenience stores. To open the key fob, you'll also require an appropriate pair (latex or not) of gloves and a small screwdriver with a flat head. Before you begin, make sure to check your owner's manual for specific steps and directions.
Once you have the new battery, take out the old one by turning the fob over and looking at the backside. There is a tiny catch that must be released by pulling it downwards. This will release the mechanical key from its original position inside the fob.
Install the new battery and ensure that it is aligned correctly. Close the fob when the battery is installed and then press the two sides of the fob together. Test your key fob after you've completed this step by pressing the unlock button. You'll be able to use the many features of your Nissan if everything is working properly. After replacing the battery, it's a good idea re-program your key fob to make sure that it works correctly.
Replace the Transmitter
Your key fob is the "key" for many of your vehicle's vital functions. It could be a major loss when it is damaged or lost. If your key fob is dead or damaged key fob, you'll be left without the ability to lock or start your vehicle.
It's a good idea to keep an extra key fob in your possession in case of need. Fortunately, the process of replacing your Nissan key fob is quite simple. The procedure for replacing the Nissan key fob is fairly simple. You'll require an additional flathead screwdriver as well as an entirely new battery to replace the old.
You'll also need a Panasonic CR2032 3V round battery (you can purchase them in multipacks priced less than $5 USD). The battery is located in the back half of the key fob. You'll need a small screwdriver with a flat head to gently break the two halves. Utilize a small flathead screwdriver to push the clip on the top of the battery to remove it, taking note of the position. Replace the battery and put the key fob back together. Test it to make sure it works correctly.
Nissan Intelligent Keys eventually wear out and require to be changed, just like any other electronic device. Secure your key fob from water, magnetic fields and physical impacts. Don't drop it or put too much pressure on the device.
Replace the Key
If your Nissan key fob has gone out you won't be able to use it to unlock or start your car. That's a problem for people who need to get to work in Detroit, run errands near Dearborn or enjoy an evening out near Troy.
It's not too difficult to change the battery in your Nissan Smart Key. You can replace the battery at home, or at the dealership. The cost of a replacement pack is usually $5 or less.
Begin by flipping over the fob and pressing a small catch on the back. This will release the emergency key that is mechanical. The emergency key won't allow you to start your vehicle however, it will allow you to open the door.
Then take a look for a small gap on the top of the casing for the key fob. These are the perfect place to insert an screwdriver through, allowing you to pry the two pieces of the key fob. Once you have access to the internal battery, pull it out and make note of the position it is in. When you're ready to put back together the key fob, slide the new battery into its place and snap the two parts of the case together. Insert the mechanical key and your Nissan smartkey will function just as normal.
Other Problems
Many modern cars are equipped with key fobs that let you to lock and start them without having the physical car key. To do this the key fob makes use of tiny transmitters to communicate with the car's computer system.
If your Nissan key fob stops working after changing the battery, there could be many reasons to blame. One reason is that the new battery might not be properly seated in the key fob. Resetting the key fob is another possibility. Luckily, this is an easy task that can be done at home with just a few tools.
For instance, you'll require an appropriate screwdriver, with preferably one with a flat-headed head to remove the key fob and then remove the battery that was in there. With a screwdriver, break the back of the keyfob and insert the new batteries. You'll also need to reset your key fob in order to allow it to function with your vehicle.
You can easily program your Nissan key fob yourself as they are all user-programmable. It is typically done by inserting the fob into the ignition twice in five seconds. If this fails, you may take your key fob into a dealer or auto locksmith to have it programmed. The cost will differ based on the person you talk to and the kind of car you own.